From: <dmcnews_at_dml_yahoogroups.com>
To: <dmcnews_at_dml_yahoogroups.com>
Subject: [DML] Digest Number 689
Date: Friday, August 31, 2001 5:19 AM

Before posting messages or replies, see the posting policy rules at:
www.dmcnews.com/Admin/rules.html

To address comments privately to the moderating team, please address:
moderator_at_dml_dmcnews.com

There are 23 messages in this issue.

Topics in this digest:

1. Re: used cats for sale
From: "HILTON HOOVER" <hjhjr_at_dml_starband.net>

2. DMC Sunshade rocks!
From: "Kevin Abato" <delorean_at_dml_abato.net>

3. Re: Re: BMW Eurofest, NC Owners and idle stall
From: dherv10_at_dml_aol.com

4. Re: Gas cap rust...
From: dherv10_at_dml_aol.com

5. Re: Gas cap rust...
From: "David Swingle" <dswingle_at_dml_enteract.com>

6. Re: Fuse question
From: dherv10_at_dml_aol.com

7. Eurofest '01
From: "Sean Howley" <delorsche_at_dml_att.net>

8. Re: GM Engine
From: "Richard Cutter" <dmc_power_at_dml_hotmail.com>

9. RE: Gas cap rust...
From: "Buckner, William" <William.Buckner_at_dml_pfizer.com>

10. RE: Fuse question
From: "Marc A. Levy" <malevy_at_dml_paramanet.com>

11. Re: Winner of the Gold DeLorean
From: Dmc3360_at_dml_aol.com

12. Re: Fuse question
From: wilhelm starberg <wilm_at_dml_c2i.net>

13. Re: Re: GM Engine
From: "Walter" <Whalt_at_dml_att.net>

14. Re: Fuse question
From: jtrealty_at_dml_webspan.net

15. Re: Winner of the Gold DeLorean
From: Al Nelson <z52vette_at_dml_yahoo.com>

16. Re: Re: Engine Stalling
From: "DMC Joe" <dmcjoe_at_dml_att.net>

17. Re: Re: GM Engine
From: "DMC Joe" <dmcjoe_at_dml_att.net>

18. Euro 2001
From: lovdmc12_at_dml_aol.com

19. Re: Gas cap rust...
From: srubano_at_dml_optonline.com

20. Re: Eurofest '01
From: "DMC Joe" <dmcjoe_at_dml_att.net>

21. DeLorean Fall Foliage Tour
From: turbodmc_at_dml_hotmail.com

22. It's the little things...!
From: Les Huckins <jhuckins_at_dml_cybersurfers.net>

23. Re: Fuse question
From: "DMC Joe" <dmcjoe_at_dml_att.net>





Message: 1
Date: Wed, 29 Aug 2001 04:59:19 -0500
From: "HILTON HOOVER" <hjhjr_at_dml_starband.net>
Subject: Re: used cats for sale

[Moderator Note: Henceforth, please send "I want to buy what you are selling" responses directly to the other party.  If you want to discuss the DeLorean catalytic converter system feel free to post you question to the DML.]

I am interested in one of your catalytic converters if the are made for the
delorean and are in good shape.  thanks   Hilton Hoover
----- Original Message -----
From: <delorean502_at_dml_excite.com>
To: <dmcnews_at_dml_yahoogroups.com>
Sent: Wednesday, August 29, 2001 9:29 AM
Subject: [DML] used cats for sale


>
> I have about 4 used CATS that I want to get rid of.  They all have
> about 20K on them.  Use them as replacements, use them for testing,
> hollow one out, whatever.  I'm selling them for $20 each.  If anyone
> is interested, let me know.  They all appear to be ok inside, but I'm
> not going to guarentee anything.  I will guarentee that they will
> fit :)
>
> Erik
>
>
>
> Before posting messages or replies, see the posting policy rules at:
> www.dmcnews.com/Admin/rules.html
>
> To address comments privately to the moderating team, please address:
> moderator_at_dml_dmcnews.com
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>




________________________________________________________________________
________________________________________________________________________


Message: 2
Date: Wed, 29 Aug 2001 18:02:45 -0400
From: "Kevin Abato" <delorean_at_dml_abato.net>
Subject: DMC Sunshade rocks!

I love my Delorean, but it seems to think it should have lived it's life as
a pizza oven.  I have been working with PJ Grady for several weeks to nail
down a small freon leak in the AC unit, but so far we have had no luck.

To keep cool in the mean time, I decided to order one of the custom fit
window shades from DMC Houston.  Let me say this.....IT MAKES A BIG
DIFFERENCE!  The fact that the shade sits outside the window means that no
sunlight magnifies through at all.  The inside temp. of the car today was
great, and it helps protect the interior without having to get a dashboard
mat.

Just wanted to let you all know in case you were pondering getting one for
yourself.

P.S.  i am thinking of modifying the shade slightly.  I want to put an
elastic band that goes across the top part from torsion bar to torsion bar
(something that will stretch tight, and have velcro in the middle to hook
together)  This should give it a slightly snugger fit on the top.




________________________________________________________________________
________________________________________________________________________


Message: 3
Date: Wed, 29 Aug 2001 19:15:01 EDT
From: dherv10_at_dml_aol.com
Subject: Re: Re: BMW Eurofest, NC Owners and idle stall

Joe, I would replace the 02 sensor and readjust the air flow meter. This is 
provided your idle motor, switch and all the idle circuit is in good shape. 
John hervey
http://www.specialtauto.com/



________________________________________________________________________
________________________________________________________________________


Message: 4
Date: Wed, 29 Aug 2001 19:16:38 EDT
From: dherv10_at_dml_aol.com
Subject: Re: Gas cap rust...

I use a dremmel tool with a brush, but it's hard to seal it so it won't rust 
again. I now have POR15 and an going to retry it.
John Hervey



________________________________________________________________________
________________________________________________________________________


Message: 5
Date: Wed, 29 Aug 2001 22:33:22 -0000
From: "David Swingle" <dswingle_at_dml_enteract.com>
Subject: Re: Gas cap rust...

Glass-Bead blaster.

Dave
(Me neither, but then again I don't live in CA)

--- In dmcnews_at_dml_y..., RJRavalli_at_dml_A... wrote:
> Perhaps a silly question, but what is the best way to get rust off 
a badly rusted gas cap?
> 
> Richard
> Modesto, CA
> (no, I never voted for Gary Condit)




________________________________________________________________________
________________________________________________________________________


Message: 6
Date: Wed, 29 Aug 2001 19:20:49 EDT
From: dherv10_at_dml_aol.com
Subject: Re: Fuse question

Johndmc, To get the correct amperage, you would have to put an DC amp meter 
in line to get the correct current draw.
John Hervey
http://www.specialtauto.com/



________________________________________________________________________
________________________________________________________________________


Message: 7
Date: Wed, 29 Aug 2001 21:17:27 -0400
From: "Sean Howley" <delorsche_at_dml_att.net>
Subject: Eurofest '01

Just a reminder that the Eurofest show is coming up soon.  Registrations will be taken up to Oct. 14.  We need to try to have a strong showing this year.  There is rumor that the DeLorean might be next years featured marque, but to do this, we really need to have everyone come that can!  Especially you guys in Atlanta.  The event starts the evening of Oct. 19 (Friday) and ends the 21 (Sunday) with the show itself taking place on the 20th.  The show is a full day event and is absolutely fabulous.  Any European car can be involved - not just British!  It takes place on the BMW assembly plant grounds.  To get more information about the show as well as the registration form, please see http://www.euroautofestival.com.

I hope to see a lot of you there!

Sean Howley
VIN#2345


[Non-text portions of this message have been removed]




________________________________________________________________________
________________________________________________________________________


Message: 8
Date: Thu, 30 Aug 2001 01:22:36 +0000
From: "Richard Cutter" <dmc_power_at_dml_hotmail.com>
Subject: Re: GM Engine

Hello Blake....

I have been working with engine conversions for many years, mainly in the 
Pontiac Fiero.   In these cars my choice is the 3800 S/C but when
it came around to the Delorean I chose the Cadillac Northstar.  Being
an aluminum block/heads it replaces the old 2.8 PRV with only 35 lbs
addition in weight.  This is far less than the 3800 would be...

Also the 3800 has far higher low end torque than the N* and would be
harder on the transmission.  Looking at the spec.  sheets they are a
close match but in the car you can tell a large differance.   The DMC
transmission ( as does any ) is sensitive to torque loading and the
lesser amount at low RPM will allow longer transmission life.

Since I completed the conversion about 2 years ago G/M has produced a
V-6 version of the N* and is a far better match to the DMC.
The N* is almost ( watch the strong replies come in ) over-kill for
it at 300 hp.  The 210 hp out of the 3.5 TOHC V6 Version, lighter weight
( 50 or more lbs.) and shorter length will make it ideal ( my opinion )

See my web page at www.americancustomeng.com

By the way my DMC with the N* is driven almost daily....

I hope this helped a little

Rich Cutter


>From: "Blake Grover" <blakeistheman_at_dml_hotmail.com>
>
>Hi,
>  I'm going to be converting my Delorean's engine over to a 3.8 GM engine 
>and I was wondering if you had any tips for me when I convert mine over.  
>How do you get the engine to hook up to the transmission?  IF you have any 
>suggestions I would appreciate it.
>
>Thanks!
>Blake Grover
>


_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp




________________________________________________________________________
________________________________________________________________________


Message: 9
Date: Thu, 30 Aug 2001 07:20:40 -0400
From: "Buckner, William" <William.Buckner_at_dml_pfizer.com>
Subject: RE: Gas cap rust...

Replace it



Bill Buckner

Instrumentation Supervisor
Electrical and Instrument Dept.
Pfizer, Inc.
Global Manufacturing
Holland, MI Facility
   %   Phone:  616-392-2375  x-2449
 *   Fax:      616-392-8267
     *  Email:    william.buckner_at_dml_pfizer.com


[Duplicate quote snipped by moderator]



________________________________________________________________________
________________________________________________________________________


Message: 10
Date: Thu, 30 Aug 2001 07:49:39 -0400
From: "Marc A. Levy" <malevy_at_dml_paramanet.com>
Subject: RE: Fuse question

It is ALWAYS a bad idea to install a fuse that is higher that what was
there previously unless you know every piece of wire and connection in
the circuit is good for the higher rating.

If for some reason you sustain 14.5A for a extended period of time on
the circuit, and the wires are only rated for 10A... you got yourself a
fire!

Maybe someone else on the list is more familiar with that circuit than
I, and confirm if (or not) the wires and connections can handle 15A.


-----Original Message-----
> From: johndmc57_at_dml_yahoo.com [mailto:johndmc57_at_dml_yahoo.com]
> Sent: Wednesday, August 29, 2001 9:53 AM
> To: dmcnews_at_dml_yahoogroups.com
> Subject: [DML] Fuse question


> I noticed that I had no brake lights. The fuse was broken.
> It calls for a 10 amp fuse. I recently connected a third
> tail light that came installed on the car mounted on the
> luvures. I put in a 15 amp fuse for the tail lights . . .

[moderator snip]



________________________________________________________________________
________________________________________________________________________


Message: 11
Date: Thu, 30 Aug 2001 09:01:57 EDT
From: Dmc3360_at_dml_aol.com
Subject: Re: Winner of the Gold DeLorean

I thought the Gold DeLorean in the bank in Snyder was one of the two original 
American Express cars.  Also the one in the bank in Snyder had a black 
interior.  The other American Express car has the saddle interior and is in a 
museum.  The third gold DeLorean is the one in Maryland and it is for sale 
and was at the Cleveland show.  It was the last one made using spare panels 
originally produced for the two original cars and also has a saddle interior. 
 Reading the article on Joe's website it says the car for sale in Maryland 
was the one in the Snyder Bank.  Didint seem correct to me but I may be wrong.

Gary

<<Message: 11
>   Date: Wed, 29 Aug 2001 10:38:11 -0400
>   From: "DMC Joe" <dmcjoe_at_dml_att.net>
>   Subject: Re: Winner of the Gold DeLorean

[moderator snip]

> Click on this DMC.tv link for the latest information on
> the Gold DeLorean
>  http://www.geocities.com/dmcjoe/gold.html .

> DMC Joe



________________________________________________________________________
________________________________________________________________________


Message: 12
Date: Thu, 30 Aug 2001 16:46:29 +0200
From: wilhelm starberg <wilm_at_dml_c2i.net>
Subject: Re: Fuse question


29.08.01 15:53:19, johndmc57_at_dml_yahoo.com wrote:
[snip]
>I put in a 15 
>amp fuse for the tail lights because with the addition of the third 
>tail light a 10 amp may not be enough. Is my thinking correct or am I 
>making a mistake. What is and how do you figure the amp load of your 
>brake light circit.

How to figure out the load:

I(ampere) = P(watt) / U(volt) 

(P = total power of the lights in the circuit)

Keep in mind that the wires may not be built for more than 10A - and might melt or take fire.

Regards,
Wilhelm Starberg
Norway #10816









________________________________________________________________________
________________________________________________________________________


Message: 13
Date: Thu, 30 Aug 2001 10:35:44 -0400
From: "Walter" <Whalt_at_dml_att.net>
Subject: Re: Re: GM Engine

Richard,

I would love to hear more about your Cadillac Northstar engine conversion.
Can you say what models & years Cadillac have these engines?  Were you able
to hook up all the associated electronics to allow the engine to run on
'limp home' mode with no radiator coolant?

I was talking to a local Camero affectionado who thinks that his LS-1 block
is the same size as the Northstar V8.  Is this so?  He says that the block
is available in aluminum.  If it would fit, it would make a lot more sense
to use since more aftermarket parts are available.  I just don't see old men
at car shows tricking out their Caddies like I do with kids & their Chevys.

I would like to consider installing a front wheel drive engine &
transmission in place of the DeLorean stuff.  Has anyone considered this
idea?  If the drive axle doesn't line up then I suppose an extra set of CV
joints with interconnecting axles held on bearings should work just fine.
I'm not afraid to do whatever it takes.

Walt    Tampa, FL




________________________________________________________________________
________________________________________________________________________


Message: 14
Date: Thu, 30 Aug 2001 15:35:18 -0000
From: jtrealty_at_dml_webspan.net
Subject: Re: Fuse question

It could be that the wire running to the third brake lite is pinched 
and is blowing the fuse (which may be why it was disconnected). 
Disconnect it and see if the fuse holds. I reccomend that where you 
tap off for the third lite that you stick a separate fuse just for the 
third lite itself. Now if the wire gets grounded you still have your 
origional lites going. As for the third brake lite you should install 
an L.E.D. type. They have a very low current draw and are very bright 
and noticeable. NEVER overfuse. Mount the lite as high on the rear 
louvre as you can and use double stick tape. Carefully route the wire 
as it has to pass many sharp edges. Leave enough slack so the louvre 
opens without streching the wire and you can remove and install the 
plastic valence strip. Make sure you get a good ground connection. 
This is one of the cheapest and best things you can do to make the car 
more noticeable to other drivers. Another simple and inexpensive tip 
is to add tiny convex mirrors (with double stick tape again) to the 
side rear view mirrors. These will help increase your visibility to 
the rear.
David Teitelbaum
vin 10757

-
- In dmcnews_at_dml_y..., johndmc57_at_dml_y... wrote:
> I noticed that I had no brake lights. The fuse was broken.
> It calls for a 10 amp fuse. I recently connected a third tail light 
> that came installed on the car mounted on the luvures. I put in a 15 
> amp fuse for the tail lights because with the addition of the third 
> tail light a 10 amp may not be enough. Is my thinking correct or am 
I 
> making a mistake. What is and how do you figure the amp load of your 
> brake light circit.




________________________________________________________________________
________________________________________________________________________


Message: 15
Date: Thu, 30 Aug 2001 07:47:24 -0700 (PDT)
From: Al Nelson <z52vette_at_dml_yahoo.com>
Subject: Re: Winner of the Gold DeLorean

Question:  The picture of the gold DeLorean on Joe's
website indeed looks like the last car, vin 20105,
since it was supposedly the only one with the
camel-colored interior (right?).  But the description
makes it sound like it was the one from Snyder Bank. 
I thought the Snyder Bank D was one of the two AMEX
cars (with gray or black interior, I'm not sure). 
This web site with pictures of the gold Snyder
Delorean shows the interior being either black or gray
(hard to tell with the lighting...looks black to me). 


http://bigtexas.com/dmc/

Is the AMEX car still in Snyder or, if it is gone,
where is it?  The pics on Joe's website don't look
like they are of the same car.  

Curious minds want to know.

Al

[duplicate quote snipped by moderator]



________________________________________________________________________
________________________________________________________________________


Message: 16
Date: Thu, 30 Aug 2001 10:48:55 -0400
From: "DMC Joe" <dmcjoe_at_dml_att.net>
Subject: Re: Re: Engine Stalling

Joe,

Your problem is related to the idle speed circuit. Check to be certain the idle speed motor is operational. This is easily accomplished by disconnecting and reconnecting the idle speed motor electrical connection while the engine is at idle. If there is no change in the idle speed during this test your idle speed motor or associated electrical circuit may be defective.
 
DMC Joe
www.dmc.tv 
"See You At The Cruise-In"
DMC Help / De Lorean Services / <dmchelp_at_dml_att.net>


  ----- Original Message ----- 
>  From: jpalatinus_at_dml_earthlink.net 
>  To: dmcnews_at_dml_yahoogroups.com 
>  Sent: Wednesday, August 29, 2001 12:10 PM
>  Subject: [DML] Re: BMW Eurofest, NC Owners and idle stall
>
>
>  My car has been doing great for these first few weeks of classes, 
>  but when I have the AC on, it tends to stall at low rpms, like when 
>  I idle at the stoplights.  

[moderator snip]



________________________________________________________________________
________________________________________________________________________


Message: 17
Date: Thu, 30 Aug 2001 10:40:21 -0400
From: "DMC Joe" <dmcjoe_at_dml_att.net>
Subject: Re: Re: GM Engine

Correct me if I'm wrong but from past postings on the DML I believe the Northstar engine conversion has a price tag of around $20,000. 

I believe that this information should me mentioned along with the technical specifications. Personally I think that anytime a single system replacement, that being the drivetrain in this situation, exceeds the price of the entire vehicle; questions should be raised as to weather this would be a cost effective conversion.

DMC Joe
www.dmc.tv 
"See You At The Cruise-In"
DMC Help / De Lorean Services / <dmchelp_at_dml_att.net>


  ----- Original Message ----- 
>  From: Richard Cutter 
>  To: blakeistheman_at_dml_hotmail.com 
>  Cc: dmcnews_at_dml_yahoogroups.com 
>  Sent: Wednesday, August 29, 2001 9:22 PM
>  Subject: [DML] Re: GM Engine
>
>
>  Hello Blake....
>
>  I have been working with engine conversions for many years, mainly in the 
>  Pontiac Fiero.   In these cars my choice is the 3800 S/C but when
>  it came around to the Delorean I chose the Cadillac Northstar.

[moderator snip]




________________________________________________________________________
________________________________________________________________________


Message: 18
Date: Thu, 30 Aug 2001 16:40:33 EDT
From: lovdmc12_at_dml_aol.com
Subject: Euro 2001

I got an email from the Euro 2001 show at the BMW factory in Greer, SC and 
was told that only 3 DeLoreans have preregistered.  Ms. Harrbison also told 
me that tours and the hotel are filling up fast, so make your reservations 
and arrangements to be there now.  I hope we can have a good showing this 
year.  The show is great and a lot of fun.

I hope to see you there this October!

Brian
VIN 1597



________________________________________________________________________
________________________________________________________________________


Message: 19
Date: Thu, 30 Aug 2001 18:40:01 -0000
From: srubano_at_dml_optonline.com
Subject: Re: Gas cap rust...

The (non-locking) gas caps ar very cheap...about $10 from a DMC parts 
vendor. If you want to clean it up the best way is glass bead it or 
you can use a dremel tool. To keep it from rusting again, paint it 
with some POR-15...I used this on my chassis (had the entire thing 
sandblasted then I painted it with the POR-15) and it is FANTASTIC! 
never have a rust problem again and it is just as strong as powder 
coating.

Steve

--- In dmcnews_at_dml_y..., RJRavalli_at_dml_A... wrote:
> Perhaps a silly question, but what is the best way to get rust off 
a badly rusted gas cap?
> 
> Richard
> Modesto, CA
> (no, I never voted for Gary Condit)




________________________________________________________________________
________________________________________________________________________


Message: 20
Date: Thu, 30 Aug 2001 13:11:25 -0400
From: "DMC Joe" <dmcjoe_at_dml_att.net>
Subject: Re: Eurofest '01

Sean,

Thanks for the information. If you are attending the Cruise-In Show we would be happy to give you some time to address the attendees with this information. This could be a great opportunity for people to sign-up for early registration information for the Eurofest show.

DMC Joe
www.dmc.tv 
"See You At The Cruise-In"
DMC Help / De Lorean Services / <dmchelp_at_dml_att.net>


>  ----- Original Message ----- 
>  From: Sean Howley 
 
>  Subject: [DML] Eurofest '01


>  Just a reminder that the Eurofest show is coming up soon.

[moderator snip]






[Non-text portions of this message have been removed]




________________________________________________________________________
________________________________________________________________________


Message: 21
Date: Thu, 30 Aug 2001 19:24:14 -0000
From: turbodmc_at_dml_hotmail.com
Subject: DeLorean Fall Foliage Tour

The second annual DeLorean Fall Foliage Tour has finally been 
scheduled. This should be the largest DeLorean event in the Northeast 
this fall!

This year it will be a two day event Saturday  & Sunday October 27th 
and 28th.

On Saturday the event starts at PJ Gradys in West Sayville N.Y.
This is guaranteed to be interesting to all DeLorean Enthusiasts

We will then depart from PJ Gradys and Caravan out to the East End of 
Long Island.
This will include a driving tour with stops along the way in the 
Hamptons and finish at the end of Long Island at the Montauk Light 
house. We will have dinner in Montauk and Caravan back to 
the hotel in East Hampton for a late check in at East Hampton House. 
We have a special hotel rate of $75 + tax but you must tell them you 
are part of the DeLorean Fall Tour (631) 324-4300 Fax 631 329-3743
On the web http://www.duneresorts.com/ehhouse.html
 
Sunday the tour continues and we will take a short ferry ride to 
Shelter Island that may include a road rally and then departs on a 
different ferry to the North Fork of Long Island. We will have a late 
lunch in Green Port and will spend some time exploring the town. I am 
trying to arrange a winery tour also.

This trip will take you through the Long Island you have heard about 
but never seen.
With the help of the people From the DeLorean Mid Atlantic I hope to 
add a few more events during this weekend, this will be an event you 
don't want to miss! 

Please make your hotel reservations early so you get a room, 
accommodations are limited.
The hotel takes credit cards but requires a deposit up front (this is 
standard for this part of the world).

If you think you may want to attend or need more information please 
e-mail me privately at turbodmc_at_dml_hotmail.com
Knowing approximately how many people are interested will make it 
easier to plane this event.
If people from New England need ferry information to get to Long 
Island I can provide that to you.
I will be posting more information as I finalize some of the details. 


Regards,

Michael DeLuca











________________________________________________________________________
________________________________________________________________________


Message: 22
Date: Thu, 30 Aug 2001 13:46:58 +0000
From: Les Huckins <jhuckins_at_dml_cybersurfers.net>
Subject: It's the little things...!

Like the exhaust tips!  My '82 has these great looking exhaust tips.
I've recently purchased an '83 and it has just the polished
pipes...pathetic!  Does anyone have a lead to emulation tips?  Pipes are
about 1 3/4" OD, Tip OD is about 2 1/2" (slant cut, of course).  Please
help if you can, I'm burning up a lot of time in this hunt.  (Or hey, if
you're destroying something that you can remove the tips from that might
work too, I'm open).

Thanks, Les




________________________________________________________________________
________________________________________________________________________


Message: 23
Date: Thu, 30 Aug 2001 09:35:20 -0400
From: "DMC Joe" <dmcjoe_at_dml_att.net>
Subject: Re: Fuse question

With the exception of fuse # 7, all of the circuit fuse ratings are conservatively rated. Concerning the brake light circuit, one extra bulb will not overwhelm the 10 amp fuse. The 15 amp fuse will continue to provide overload protection therefore you can continue to use that fuse in the brake light circuit.

CAUTION: When replacing fuses in the fuse block inspect the condition or the fuse connectors for the fuse you are replacing. Any signs of corrosion, overheating, or distortion will require replacement with a heavy duty in- line fuse replacement. Additionally any signs of melting of the fuse block for that particular fuse will also require an in-line replacement. 

DMC Joe
www.dmc.tv 
"See You At The Cruise-In"
DMC Help / De Lorean Services / <dmchelp_at_dml_att.net>


  ----- Original Message ----- 
  From: johndmc57_at_dml_yahoo.com 
  To: dmcnews_at_dml_yahoogroups.com 
  Sent: Wednesday, August 29, 2001 9:53 AM
  Subject: [DML] Fuse question


  I noticed that I had no brake lights. The fuse was broken.
  It calls for a 10 amp fuse. I recently connected a third tail light 
  that came installed on the car mounted on the luvures. I put in a 15 
  amp fuse for the tail lights because with the addition of the third 
  tail light a 10 amp may not be enough. Is my thinking correct or am I 
  making a mistake. What is and how do you figure the amp load of your 
  brake light circit.








[Non-text portions of this message have been removed]




________________________________________________________________________
________________________________________________________________________



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/