From: <dmcnews_at_dml_yahoogroups.com>
To: <dmcnews_at_dml_yahoogroups.com>
Subject: [DML] Digest Number 1698
Date: Monday, October 06, 2003 6:43 PM

To address comments privately to the moderating team, please address:
moderators_at_dml_dmcnews.com

For more info on the list, tech articles, cars for sale see www.dmcnews.com

To search the archives or view files, log in at http://groups.yahoo.com/group/dmcnews

There are 25 messages in this issue.

Topics in this digest:

1. Re: Source of LED bulb replacements
From: "content22207" <brobertson_at_dml_carolina.net>

2. Re: kicked in the you-know-where
From: "David Teitelbaum" <jtrealty_at_dml_webspan.net>

3. 1983 DeLorean for sale now on website...
From: NJP548_at_dml_aol.com

4. New owner! A/C problems
From: casey barlow <dmc1288mph_at_dml_yahoo.com>

5. Door lock warning
From: "Payne" <bpayne_at_dml_macnet.com>

6. Re: Re: Accuracy of charging meter
From: "Payne" <bpayne_at_dml_macnet.com>

7. Frying fuses
From: "Kramer" <jettaman95_at_dml_yahoo.com>

8. Standard Transmission
From: kKoncelik_at_dml_aol.com

9. wacky indicators
From: Andrew Prentis <aprentis_at_dml_rocketmail.com>

10. cooling system hose diameter?
From: Soma576_at_dml_aol.com

11. San Diego British Car Day - you missed a good one!
From: "dmcox_sd" <dmcox_at_dml_tfb.com>

12. panels and a door for sale
From: "erikgeerdink" <erikgeerdink_at_dml_yahoo.com>

13. Removing front impact absorber
From: "Joshua Weader" <weader_at_dml_moocow.org>

14. Tuning, tuning and more tuning.
From: "cruznmd" <racuti1_at_dml_delorean.com>

15. Re: cooling system hose diameter?
From: "Dave Swingle" <swingle_at_dml_dmcnews.com>

16. Re: New owner! A/C problems
From: "David Teitelbaum" <jtrealty_at_dml_webspan.net>

17. Re: wacky indicators
From: "David Teitelbaum" <jtrealty_at_dml_webspan.net>

18. RE: New owner! A/C problems
From: "John Hervey" <john_at_dml_specialtauto.com>

19. RE: Re: Accuracy of charging meter
From: "John Hervey" <john_at_dml_specialtauto.com>

20. RE: Frying fuses
From: "John Hervey" <john_at_dml_specialtauto.com>

21. Howto #11 complete , T-panel removal
From: jordan rubin <nuttenschleuder_at_dml_yahoo.com>

22. RE: wacky indicators
From: "John Hervey" <john_at_dml_specialtauto.com>

23. 2key system set for sale
From: "erikgeerdink" <erikgeerdink_at_dml_yahoo.com>

24. BTTF halloween costumes
From: john fredt <hecklerkochgmbh_at_dml_yahoo.com>

25. Re: diode location for door ajar/delay lamps
From: "Dave Sontos" <dsontos_at_dml_sybercom.net>





Message: 1
Date: Mon, 06 Oct 2003 02:18:38 -0000
From: "content22207" <brobertson_at_dml_carolina.net>
Subject: Re: Source of LED bulb replacements

Just one of many online retailers:

http://www.trucknvans.com/bulbs/

You want 194 series.

Bought some colored bulb covers from them (application required
sideways light beams). Very satisfied with service.

Bill Robertson
#5939

>--- In dmcnews_at_dml_yahoogroups.com, "Marcel" <mbourgon_at_dml_e...> wrote:
> Martin;
> Just got my baby back and trying to sort out a few small items. 
Like the
> idea of replacing the lights in doors with the diodes you just
mentioned.
> Where can one buy these and what exactly are we looking for.  Help
would be
> greatly appreciated
> Marcel in El Paso



________________________________________________________________________
________________________________________________________________________


Message: 2
Date: Mon, 06 Oct 2003 02:29:09 -0000
From: "David Teitelbaum" <jtrealty_at_dml_webspan.net>
Subject: Re: kicked in the you-know-where

As stated in the last post for a private individual the biggest
advantage in leasing is the chance to drive a better car than you can
afford. There are much better reasons for a business to lease cars.
All the interest and, under the right terms, the depreciation are
deductable expenses. For most businesses rolling stock, as the cars
and trucks are refered to, are completely depreciated by the end of
the term of the lease anyway. It keeps the average age of the fleet
young and the repair costs low and the reliability high. For most
private people the best way to own a car is to own it as long as
possible to average out the high depreciation of the first years. If
you finance the car you can sell it at the end of the term for
whatever you can get, not so in a lease (read rental). This implies
that it will be well maintained so as it gets older it doesn't kill
you with high operating and maintaince costs. Most owners as a general
rule neglect maintaince so this is difficult to do. The other thing
working against you is the advertising trying to entice you into the
newest, latest and greatest. If you have to borrow money to buy a
Delorean IMHO you should rethink the reasons you want the car. In
addition to the purchase price you have insurance, storage, parts, and
labor. The worst of all cases is to have to stretch to make the
payments and not be able to afford the repairs so you can't even drive
the car if it breaks down.
David Teitelbaum
vin 10757



________________________________________________________________________
________________________________________________________________________


Message: 3
Date: Sun, 5 Oct 2003 22:48:24 EDT
From: NJP548_at_dml_aol.com
Subject: 1983 DeLorean for sale now on website...

Hey List,

    I just started to create a website describing my De Lorean for sale.  Its 
not done yet, but I figured I should put something out there for everyone 
whos interested in it.  Please check it out and e-mail me if you're interested or 
if you have any questions at all.  Thanks a lot and have a great night!

http://members.aol.com/njp548/test.html

Later,
Nick Pitello
15914
<A HREF="Http://members.aol.com/njp548">Http://members.aol.com/njp548</A>


[Non-text portions of this message have been removed]




________________________________________________________________________
________________________________________________________________________


Message: 4
Date: Sun, 5 Oct 2003 20:13:12 -0700 (PDT)
From: casey barlow <dmc1288mph_at_dml_yahoo.com>
Subject: New owner! A/C problems

 HI  everyone,  I'm the new owner of vin 3270, a 5 spd
with gray interior, and is not painted. I have wanted
one for about 12 years, its been a long wait!!! But
enough of that, Here's the problem, with the a/c on it
gets cold, and you can hear the fan blowing hard but
very little air comes out of the vents. It is getting
vacume to the switch, but something ain't right.
Thanks Casey

__________________________________
Do you Yahoo!?
The New Yahoo! Shopping - with improved product search
http://shopping.yahoo.com



________________________________________________________________________
________________________________________________________________________


Message: 5
Date: Sun, 5 Oct 2003 20:37:30 -0700
From: "Payne" <bpayne_at_dml_macnet.com>
Subject: Door lock warning

I finally got one of the label kits from DeLorean Motor Company and saw the
warning "Do not operate lock when doors are open."  What exactly will occur
if the locks are activated on open doors?  The reason I ask is because I'm
having an unusual problem with my door locks where the driver's side is
constantly trying to lock itself and no matter how hard I push it will never
move the lever to the fully unlocked position.  It's not a problem with the
solenoid, it just physically won't move to the open position easily.  Most
of the time I have to hold the lock open while I pull the door handle just
to open it, this only really happens in hot weather.  One of the lock rods
is vibrating against the inner door structure and I think it may be bent.
I'm looking to replace the rear latch since I have an extra but I will get
to that in another post.  I've got classes at night so I need the time
first.

payne
proud owner of #2975, sometimes she just won't let me leave her.


---
[This E-mail Scanned for viruses by Onlinemac.com]




________________________________________________________________________
________________________________________________________________________


Message: 6
Date: Sun, 5 Oct 2003 20:37:32 -0700
From: "Payne" <bpayne_at_dml_macnet.com>
Subject: Re: Re: Accuracy of charging meter

Mine moves normally, but it seems to drop quite a bit while using
acessories.  At normal idle with no lights on the needs sits above the 13
volt mark.  If I have the high beams on with the brake lights it drops
drastically and everything dims.  Thanks for the info, I'm probably looking
at getting an upgraded alternator to deal with the load.

payne


> The voltmeter is pretty accurate when it is working right. If it is
> always on the low side check it with an accurate voltmeter. It could
> be that your alternator and-or battery need to be replaced or that you
> need to clean up the connections in the binnacle and the main
> grounding point inside by the front left tire. If it reads too high
> that would indicate a bad voltage regulater inside the alternator.
> David Teitelbaum
> vin 10757
>



---
[This E-mail Scanned for viruses by Onlinemac.com]




________________________________________________________________________
________________________________________________________________________


Message: 7
Date: Mon, 06 Oct 2003 03:54:16 -0000
From: "Kramer" <jettaman95_at_dml_yahoo.com>
Subject: Frying fuses

Dear List,
  I recently came across an unusual problem. I never changed the temp 
guage around but with the lower temps I decided to change over to the 
warmer side. But when I did my radio and the AC console lights both 
shut off and my windows won't go up or down. I hear a switch click or 
something in the back and then everything does down.
  When I check my fuses the one that is broken is the one that 
controls all those parts. I replace it and I turn the temp around 
again and the fuse breaks. Why is this happening and how can I stop 
it?
  Thanks,
      Kramer
      ~#10610




________________________________________________________________________
________________________________________________________________________


Message: 8
Date: Mon, 6 Oct 2003 00:00:05 EDT
From: kKoncelik_at_dml_aol.com
Subject: Standard Transmission

I have a transmission available.
IT is a 5 speed and is being refurbished at Bowlens Transmission (Add will be 
in next issue of DeLorean Car Show Magazine)
It will be available in a few weeks so if anyone needs a transmission please 
contact me privately.

If you want it as is then it is avail now.  It has 25Kmiles.

Ken


[Non-text portions of this message have been removed]




________________________________________________________________________
________________________________________________________________________


Message: 9
Date: Sun, 5 Oct 2003 21:21:14 -0700 (PDT)
From: Andrew Prentis <aprentis_at_dml_rocketmail.com>
Subject: wacky indicators

Driving my D today I've noticed my indicators are
acting strangely.Sometimes they work,sometimes they
don't.They even come on on their own.The hazard lights
are also not working.Needless to say I want to fix
this ASAP.I was wondering could this be a bad flasher
unit?I also want to clean the earth for the indicator
circuit to see if that fixes it.Is it in that group of
earths near the front left wheel?
Any ideas welcome
Thanks,
Andrew
VIN 2883
Sydney,Aus.


__________________________________
Do you Yahoo!?
The New Yahoo! Shopping - with improved product search
http://shopping.yahoo.com



________________________________________________________________________
________________________________________________________________________


Message: 10
Date: Mon, 6 Oct 2003 08:05:14 EDT
From: Soma576_at_dml_aol.com
Subject: cooling system hose diameter?

List,

I need to replace my thermotime switch either today or tomorrow but when i 
drain my coolant to avoid making a mess on the front of my engine, i want to 
replace the two flexible radiator hoses on the bottom of the car (this will drain 
most of it anyway).  these are the hoses that make the angle from straight 
metal lines under the car to the metal hoses that go upward to the engine.  i am 
referring to part 43 on Houston's site (cooling system), or 105994 in the 
parts manual.  

i want to source these locally to save time and i need to know the length and 
diameter that i need before i start this job.

thanks!
Andy


[Non-text portions of this message have been removed]




________________________________________________________________________
________________________________________________________________________


Message: 11
Date: Mon, 06 Oct 2003 13:23:36 -0000
From: "dmcox_sd" <dmcox_at_dml_tfb.com>
Subject: San Diego British Car Day - you missed a good one!

Even though mine was the only Delorean there yesterday, it was a fine 
day.  They produce a large program for the event, including a color 
center spread featuring pictures from last year's event.  My Delorean 
made that collection!  They placed me next to the Lotus group, so it 
was great fun to compare/contrast with our automotive cousins.  My 
car tied for 1st place in the "Other" category, but lost the run-
off.  This is California, can I have a recall? ;)  I had lots of 
people come by to look and ask questions.  The highlight though was 
one gentleman with a British accent who seemed very knowledgeable 
about the car.  He introduced himself as Alan Cross, and he used to 
be chief engineer for Delorean.  He spent quite some time telling me 
stories, and I am hoping to get him to attend our local events.

One thing for your calendars: April 17, 2004 will be the 9th Annual 
Rolling British Car Day.  This will be the 9th annual event.  For 
2003, they had 131 cars, including 9 Deloreans!  Many people at 
yesterday's event remembered our participation quite vividly.  I'll 
provide more information as we get closer.

Dave
vin 16367




________________________________________________________________________
________________________________________________________________________


Message: 12
Date: Mon, 06 Oct 2003 13:35:04 -0000
From: "erikgeerdink" <erikgeerdink_at_dml_yahoo.com>
Subject: panels and a door for sale

I have a couple body panels (drivers front, drivers rear, passenger 
rear, passenger door) for sale.  Drivers front has a slight bend to 
it that you can see at certain angles.  All other panels are in 
great shape.  Email me privately if you are interested.
I also have other major Delorean parts for sale like a good engine 
and 5 speed tranny.  Also certain interior parts.  Email me if you 
are intersted.

Thanks
Erik





________________________________________________________________________
________________________________________________________________________


Message: 13
Date: Mon, 6 Oct 2003 10:00:25 -0500
From: "Joshua Weader" <weader_at_dml_moocow.org>
Subject: Removing front impact absorber


I'm having a hard time figuring out how to get the front impact absorber off.  The manual says to remove the 5 bolts holding it on, which seems easy enough.  The location of the bolts would also seem obvious, with the 5 holes in the front of the absorber.  However, the only thing I see at the far end of those holes is a flat piece of metal, not a bolt head.  Are the bolts behind that piece?  And if so, how do I get to them?  I know the bolts are in there somewhere - I can see them when I look up between the edge of the foam and the front pontoon.

Any insight would be appreciated - this one has me stumped.

--Josh
#5553



________________________________________________________________________
________________________________________________________________________


Message: 14
Date: Mon, 06 Oct 2003 16:03:04 -0000
From: "cruznmd" <racuti1_at_dml_delorean.com>
Subject: Tuning, tuning and more tuning.

Since I had plugged the idle tube vacuum leak and couldn't find any 
other vacuum leaks, I have wanted to plug my O2 sensor back in, and 
let the Lambda computer try to regulate the frequency valve again.

I have a new O2 sensor. I can't find any vac leaks (which doesn't 
mean there aren't any).

I hooked up the dwell meter and watched. Since it is so much cooler 
here in Maryland now, the warm up took longer. Finally the O2 sensor 
began sending voltage.

The dwell meter exhibited a much more consistent behavior this time 
but I'm not sure it's right yet. I also read that if it wasn't 
behaving right, to run a new ground from the block to the ECU 
bracket. I did this but it didn't help.

The idle was a tad rougher, only noticable by ear. The tach never 
wavered.

The manual says the dwell meter should fluctuate between 35-45 
degrees. Mine goes to 30, climbs to 45 and just -drops- back to 30. 
The range is close, but isn't it supposed to be a steady rocking back 
and forth vs. a climb/drop sort of motion?

Thanks,

Rich
#5335




________________________________________________________________________
________________________________________________________________________


Message: 15
Date: Mon, 06 Oct 2003 16:32:12 -0000
From: "Dave Swingle" <swingle_at_dml_dmcnews.com>
Subject: Re: cooling system hose diameter?

Those are kind of strange. The driver side is 1-1/4" on both ends 
with a very slight bend to it. The passenger side is 1-1/4" on one 
end and about 1-1/2" or so on the other. Also with a slight kink. 
They are NOT straight hoses. The tube on the passenger side that 
goes "up" is larger since it is the trans cooler on Automatic cars. 
They kept it the same size on the manual cars so that the hoses would 
stay the same, although there is no reason for that particular pipe 
to be larger. 

Dave

--- In dmcnews_at_dml_yahoogroups.com, Soma576_at_dml_a... wrote:
> List,
> 
> I need to replace my thermotime switch either today or tomorrow but 
when i 
> drain my coolant to avoid making a mess on the front of my engine, 
i want to 
> replace the two flexible radiator hoses on the bottom of the car 
(this will drain 
> most of it anyway).  these are the hoses that make the angle from 
straight 
> metal lines under the car to the metal hoses that go upward to the 
engine.  i am 
> referring to part 43 on Houston's site (cooling system), or 105994 
in the 
> parts manual.  

> i want to source these locally to save time and i need to know the 
length and 
> diameter that i need before i start this job.





________________________________________________________________________
________________________________________________________________________


Message: 16
Date: Mon, 06 Oct 2003 16:49:55 -0000
From: "David Teitelbaum" <jtrealty_at_dml_webspan.net>
Subject: Re: New owner! A/C problems

Make sure the fan is rotating in the correct direction. Reverse the
wires going to the motor if it is wrong. Check that none of the vent
hoses are out of place. Watch the actuaters move as you move the mode
switch into different positions. If the mode switch is hissing get a
rebuild kit. If you try this with the doors open it isn't a good test
because the air gets blown into the doors. Check that the vent hoses
in the doors are connected too. 
David Teitelbaum
vin 10757



--- In dmcnews_at_dml_yahoogroups.com, casey barlow <dmc1288mph_at_dml_y...> wrote:
>  HI  everyone,  I'm the new owner of vin 3270, a 5 spd
> with gray interior, and is not painted. I have wanted
> one for about 12 years, its been a long wait!!! But
> enough of that, Here's the problem, with the a/c on it
> gets cold, and you can hear the fan blowing hard but
> very little air comes out of the vents. It is getting
> vacume to the switch, but something ain't right.
> Thanks Casey
> 
> __________________________________
> Do you Yahoo!?
> The New Yahoo! Shopping - with improved product search
> http://shopping.yahoo.com




________________________________________________________________________
________________________________________________________________________


Message: 17
Date: Mon, 06 Oct 2003 16:53:24 -0000
From: "David Teitelbaum" <jtrealty_at_dml_webspan.net>
Subject: Re: wacky indicators

A bad flasher would cause the lights NOT to work, never to work on
their own. My first guess would be to check the turn switch in the
steer column and the hazard switch. It is always a good idea to check
and clean all the grounding points.
David Teitelbaum
vin 10757


  --- In dmcnews_at_dml_yahoogroups.com, Andrew Prentis <aprentis_at_dml_r...> wrote:
> Driving my D today I've noticed my indicators are
> acting strangely.Sometimes they work,sometimes they
> don't.They even come on on their own.The hazard lights
> are also not working.Needless to say I want to fix
> this ASAP.I was wondering could this be a bad flasher
> unit?I also want to clean the earth for the indicator
> circuit to see if that fixes it.Is it in that group of
> earths near the front left wheel?
> Any ideas welcome
> Thanks,
> Andrew
> VIN 2883
> Sydney,Aus.
> 
> 
> __________________________________
> Do you Yahoo!?
> The New Yahoo! Shopping - with improved product search
> http://shopping.yahoo.com




________________________________________________________________________
________________________________________________________________________


Message: 18
Date: Mon, 6 Oct 2003 11:08:00 -0700
From: "John Hervey" <john_at_dml_specialtauto.com>
Subject: RE: New owner! A/C problems

Casey, The blower motor could be turning the wrong way or the center consol
vent hose  behind the vent may have slipped of.
John Hervey
www.specialtauto.com
Delorean Parts


-----Original Message-----
From: casey barlow [mailto:dmc1288mph_at_dml_yahoo.com]
Sent: Sunday, October 05, 2003 8:13 PM
To: dmcnews_at_dml_yahoogroups.com
Subject: [DML] New owner! A/C problems


 HI  everyone,  I'm the new owner of vin 3270, a 5 spd
with gray interior, and is not painted. I have wanted
one for about 12 years, its been a long wait!!! But
enough of that, Here's the problem, with the a/c on it
gets cold, and you can hear the fan blowing hard but
very little air comes out of the vents. It is getting
vacume to the switch, but something ain't right.
Thanks Casey

__________________________________
Do you Yahoo!?
The New Yahoo! Shopping - with improved product search
http://shopping.yahoo.com


To address comments privately to the moderating team, please address:
moderators_at_dml_dmcnews.com

For more info on the list, tech articles, cars for sale see www.dmcnews.com

To search the archives or view files, log in at
http://groups.yahoo.com/group/dmcnews

Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/






________________________________________________________________________
________________________________________________________________________


Message: 19
Date: Mon, 6 Oct 2003 11:16:42 -0700
From: "John Hervey" <john_at_dml_specialtauto.com>
Subject: RE: Re: Accuracy of charging meter

Payne, The original alternator has a high turn on speed and to generate any
appreciable amount of current to power the lights or fans at idle is almost
impossible.
My up graded alternators have a lower turn on speed and deliver more current
and voltage at lower RPM's. You also need to check and clean the grounds.
This will help on the low voltage and dimming.
John Hervey
  http://www.specialtauto.com/delorean-parts/alternators.html



-----Original Message-----
From: Payne [mailto:bpayne_at_dml_macnet.com]
Sent: Sunday, October 05, 2003 8:38 PM
To: dmcnews_at_dml_yahoogroups.com
Subject: Re: [DML] Re: Accuracy of charging meter


Mine moves normally, but it seems to drop quite a bit while using
acessories.  At normal idle with no lights on the needs sits above the 13
volt mark.  If I have the high beams on with the brake lights it drops
drastically and everything dims.  Thanks for the info, I'm probably looking
at getting an upgraded alternator to deal with the load.

payne


> The voltmeter is pretty accurate when it is working right. If it is
> always on the low side check it with an accurate voltmeter. It could
> be that your alternator and-or battery need to be replaced or that you
> need to clean up the connections in the binnacle and the main
> grounding point inside by the front left tire. If it reads too high
> that would indicate a bad voltage regulater inside the alternator.
> David Teitelbaum
> vin 10757
>



---
[This E-mail Scanned for viruses by Onlinemac.com]



To address comments privately to the moderating team, please address:
moderators_at_dml_dmcnews.com

For more info on the list, tech articles, cars for sale see www.dmcnews.com

To search the archives or view files, log in at
http://groups.yahoo.com/group/dmcnews

Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/






________________________________________________________________________
________________________________________________________________________


Message: 20
Date: Mon, 6 Oct 2003 11:20:36 -0700
From: "John Hervey" <john_at_dml_specialtauto.com>
Subject: RE: Frying fuses

See below.

-----Original Message-----
From: Kramer [mailto:jettaman95_at_dml_yahoo.com]
Sent: Sunday, October 05, 2003 8:54 PM
To: dmcnews_at_dml_yahoogroups.com
Subject: [DML] Frying fuses


Dear List,
  I recently came across an unusual problem. I never changed the temp
guage around but with the lower temps I decided to change over to the
warmer side.
( Krammer, What temp gauge do you mean. Dash?????)( or do you mean temp
control )

But when I did my radio and the AC console lights both
shut off and my windows won't go up or down. I hear a switch click or
something in the back and then everything does down.
  When I check my fuses the one that is broken is the one that
controls all those parts. I replace it and I turn the temp around
again and the fuse breaks. Why is this happening and how can I stop
it? ( There has to be a short )
John Hervey

  Thanks,
      Kramer
      ~#10610



To address comments privately to the moderating team, please address:
moderators_at_dml_dmcnews.com

For more info on the list, tech articles, cars for sale see www.dmcnews.com

To search the archives or view files, log in at
http://groups.yahoo.com/group/dmcnews

Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/






________________________________________________________________________
________________________________________________________________________


Message: 21
Date: Mon, 6 Oct 2003 11:20:58 -0700 (PDT)
From: jordan rubin <nuttenschleuder_at_dml_yahoo.com>
Subject: Howto #11 complete , T-panel removal

Hello all,

This is my quota for the week, im tired.  Heres the
T-panel removal for those folks who are either working
on door wiring problems or leaks.

Looks like nobody likes my guestbook, its the only way
i know if you were there or not. take a minute, leave
a message.

You can find the HOWTO in the usual location 

http://retroserver.no-ip.com/index2.html

enjoy

Jordan 11613

__________________________________
Do you Yahoo!?
The New Yahoo! Shopping - with improved product search
http://shopping.yahoo.com



________________________________________________________________________
________________________________________________________________________


Message: 22
Date: Mon, 6 Oct 2003 11:21:45 -0700
From: "John Hervey" <john_at_dml_specialtauto.com>
Subject: RE: wacky indicators

Andrew, Loose connection somewhere??????.
John

-----Original Message-----
From: Andrew Prentis [mailto:aprentis_at_dml_rocketmail.com]
Sent: Sunday, October 05, 2003 9:21 PM
To: dmcnews_at_dml_yahoogroups.com
Subject: [DML] wacky indicators


Driving my D today I've noticed my indicators are
acting strangely.Sometimes they work,sometimes they
don't.They even come on on their own.The hazard lights
are also not working.Needless to say I want to fix
this ASAP.I was wondering could this be a bad flasher
unit?I also want to clean the earth for the indicator
circuit to see if that fixes it.Is it in that group of
earths near the front left wheel?
Any ideas welcome
Thanks,
Andrew
VIN 2883
Sydney,Aus.


__________________________________
Do you Yahoo!?
The New Yahoo! Shopping - with improved product search
http://shopping.yahoo.com


To address comments privately to the moderating team, please address:
moderators_at_dml_dmcnews.com

For more info on the list, tech articles, cars for sale see www.dmcnews.com

To search the archives or view files, log in at
http://groups.yahoo.com/group/dmcnews

Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/






________________________________________________________________________
________________________________________________________________________


Message: 23
Date: Mon, 06 Oct 2003 20:17:51 -0000
From: "erikgeerdink" <erikgeerdink_at_dml_yahoo.com>
Subject: 2key system set for sale

Hi, I have a complete two key system set for sale.  It includes both 
doors, ignition, gas cap and of course the keys.  If you are 
interested please make me an offer privately.

Thanks,
Erik





________________________________________________________________________
________________________________________________________________________


Message: 24
Date: Mon, 6 Oct 2003 15:23:50 -0700 (PDT)
From: john fredt <hecklerkochgmbh_at_dml_yahoo.com>
Subject: BTTF halloween costumes


I need the people who asked me to supply them with the radiation costumes to seriously consider ordering or buying them from another source.My company has moved the chemical suits in our building to a location where I cant easily get to them without being caught.I will still do my best to get them but it may take alot more time and halloween is right around the corner.


---------------------------------
Do you Yahoo!?
The New Yahoo! Shopping - with improved product search

[Non-text portions of this message have been removed]




________________________________________________________________________
________________________________________________________________________


Message: 25
Date: Mon, 6 Oct 2003 19:25:51 -0400
From: "Dave Sontos" <dsontos_at_dml_sybercom.net>
Subject: Re: diode location for door ajar/delay lamps

Next to the gas pedal, there is a group of three diodes.

----- Original Message ----- 
From: <Soma576_at_dml_aol.com>
To: <dmcnews_at_dml_yahoogroups.com>
Sent: Saturday, October 04, 2003 8:20 PM
Subject: [DML] diode location for door ajar/delay lamps


> List,
>
> Can someone tell me exactly where the diodes are for the interior delay
> lamps/door ajar lights/running lights?  if you look on Zilla's diagram, i
am
> looking for the diodes labeled '25'.  i believe the purple/white wire
between two of
> them has a bad connection, causing my driver's door switch to be unable to
> turn on the delay lamps or door ajar lamp, yet the running lights DO work.
if
> this wire were broken or loose, it would cause exactly the problem i have.
>
> Thanks for the info -
> Andy (getting closer and closer to a 100% functioning car...)
>
>
> [Non-text portions of this message have been removed]
>
>
>
> To address comments privately to the moderating team, please address:
> moderators_at_dml_dmcnews.com
>
> For more info on the list, tech articles, cars for sale see
www.dmcnews.com
>
> To search the archives or view files, log in at
http://groups.yahoo.com/group/dmcnews
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>




________________________________________________________________________
________________________________________________________________________



Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/